Requesting a Quotation for a Coconut Dryer or Processing Line: The Data Sheet That Makes Quotes Comparable

Short answer: two quotations for “a 1,000 kg/h coconut dryer” can differ threefold in the water they actually evaporate, and therefore in the heat, fans and floor space they need. Quotes become comparable only when your enquiry fixes the basis: feed moisture and product moisture (stated as wet or dry basis), capacity as wet feed and finished output and water evaporated, operating hours, available utilities, site conditions, scope boundaries, and how performance will be tested. This article gives a data sheet to send with every enquiry for a coconut dryer or processing line, and a method for normalising the quotes you receive.

Large industrial vibratory fluid bed dryer with insulated panels
GTI jumbo vibratory fluid bed dryer. Image: GTI Group (coconutprojects.com).

It is written for procurement teams, project consultants and plant owners buying dryers or complete lines for desiccated coconut, chips, coconut flour, milk or water powders, parings, coir pith or shell products.

Why “1,000 kg/h” is not a specification

Illustrative example. A coconut product dried to 3% moisture (wet basis). Three suppliers each quote “1,000 kg/h at 50% moisture”.

What the supplier meant Dry solids Finished output Water evaporated Minimum heat to evaporate (≈2,400 kJ/kg)
1,000 kg/h wet feed at 50% wet basis 500 kg/h 515 kg/h 485 kg/h about 323 kW
1,000 kg/h finished output, feed at 50% wet basis 970 kg/h 1,000 kg/h 940 kg/h about 627 kW
1,000 kg/h wet feed at 50% dry basis (= 33.3% wet basis) 667 kg/h 687 kg/h 313 kg/h about 208 kW

The same headline hides an evaporation load anywhere from 313 to 940 kg/h. The heat column is only the theoretical minimum for evaporating water. Real dryers need more, to warm the product and air and to cover exhaust and casing losses, and that figure must come from the supplier.

Two definitions prevent most of this confusion:

  • Wet basis moisture = water ÷ total mass. Dry basis moisture = water ÷ dry solids. Convert with wet basis = dry basis ÷ (1 + dry basis). 50% dry basis is 33.3% wet basis; 3% wet basis is about 3.1% dry basis.
  • Water evaporated = wet feed − finished output, because dry solids pass through unchanged.

Our desiccated coconut plant sizing example applies the same arithmetic from nuts per hour to dryer evaporation.

The enquiry data sheet

Send this information with every enquiry. Where you do not know a value, say so and ask the supplier to state the assumption they used.

Section What to state Why it matters
Product Product name and grade; final moisture limit (wet basis) and the test method; particle size or cut; fat content; colour and microbiological requirements Sets drying end-point and temperature limits
Feed Moisture range (wet basis, minimum to maximum); temperature; particle size; fat; how it arrives (from blancher, press, cutter); stickiness or clumping Wetter feed raises evaporation sharply
Capacity Finished output (kg/h), wet feed (kg/h) and water evaporated (kg/h) at the design feed moisture; nuts per day if relevant Removes the “1,000 kg/h” ambiguity
Operation Hours per day, days per year, batch or continuous, number of product changeovers Affects cleaning access and redundancy
Thermal utilities Steam pressure and availability; or fuel type with calorific value; or thermic fluid; or hot water/waste heat Decides heater design
Electrical supply Voltage, frequency, available kVA, DG back-up Electrical load is separate from heat
Other utilities Compressed air, cooling water, process water quality, effluent limits Often omitted, then added as extras
Site Ambient temperature and humidity range, altitude, building height and footprint, indoor or outdoor Air density, humidity and layout
Hygiene Product-contact material (for example SS304 or SS316), wet or dry cleaning, access for inspection, high-care zoning Food safety and downtime
Safety Dust or fire risk (shell powder, coir dust, fines), required protection Explosion and fire protection scope
Scope boundaries Civil and structural works, utility piping, cabling, insulation, erection, commissioning, training, spares The biggest source of price differences
Documents General arrangement, P&ID, utility list, manuals, material certificates, documentation for your target markets Needed for approvals and audits
Funding Whether itemised, new-equipment quotations are needed for a bank or subsidy file Affects quotation format

The funding row matters in India. For example, CDB’s Technology Mission on Coconut excludes second-hand machinery and caps items such as electrification at set norms. Our guide to CDB subsidy rules for coconut processing units explains why itemised quotations help.

Planning a coconut dryer or processing line? Request a quotation from GTI.

Tell us your product, target capacity, raw-material data and site location. GTI Group engineers will review it and prepare a proposal for your project, in India or abroad.

Request a quotation →

Ask for energy in two separate lines

Ask each supplier to state, at the design point:

  • Thermal demand in kW, or as kg/h of steam at a stated pressure, or as kg/h of fuel with its calorific value. Also ask for specific heat consumption in kJ per kg of water evaporated.
  • Electrical load as installed (connected) kW and expected absorbed kW. Fans, vibratory drives, conveyors, atomisers and controls all add up.

An electrically heated dryer moves its whole heat duty into the electrical line, so compare tariffs before comparing totals. For choosing the heat source, gtidryers.com compares steam, thermic fluid, direct gas and biomass hot air. For verifying the figures after start-up, see its dryer energy audit guide.

Normalising the quotes you receive

  1. Rebuild each quote’s mass balance from its stated feed moisture, product moisture and capacity. Put the water evaporated side by side.
  2. Convert all heat figures to kW and to kJ per kg of water evaporated.
  3. List electrical absorbed kW separately.
  4. Mark every scope item as included, excluded or optional, using the scope-boundary row above.
  5. Compare guarantee conditions, not just guarantee numbers.
  6. Only then compare price.

Write the performance guarantee properly

A useful guarantee states the output and final moisture together with the conditions under which they are measured. It should include:

  • Feed rate and feed moisture range during the test.
  • Final moisture limit, the sampling plan and the method. For desiccated coconut, Codex CXS 177 names AOAC 925.40 for moisture.
  • Test duration in continuous operation, and the utility conditions (steam pressure, air temperature, power supply).
  • How energy consumption will be measured during the test, if it is guaranteed.
  • What happens if the guarantee is not met.

Agree whether a factory acceptance test (FAT) at the supplier’s works and a site acceptance test (SAT) after installation are required, and what each covers. Product-specific performance usually needs the SAT, because it depends on your feed.

Red flags in a quotation

  • Capacity without feed and product moisture.
  • Moisture without “wet basis” or “dry basis”.
  • A single “power” figure with no split between heat and electricity.
  • Performance claims with no test conditions.
  • Scope described as “complete” with no exclusions list.

Matching the dryer type to the product

The data sheet also helps a supplier recommend the right dryer type. Coconut products are commonly dried in a band dryer, a combination fluid bed dryer or a vibratory fluid bed dryer for solids, and a spray dryer for milk and water powders. GTI’s industrial dryer range lists these options. For shell powder, coir dust and other combustible fines, include the safety row: gtidryers.com has a checklist on preventing fires and dust explosions in dryers. For complete projects, GTI’s turnkey drying project scope runs from process design to commissioning.

FAQ

Should I specify the dryer type in my enquiry?

You can state a preference, but it is better to specify the product, feed and duty and let suppliers justify their choice. Ask them to explain why.

What if my feed moisture varies widely?

State the full range and the design point. The dryer should be sized for the wettest feed you expect at full output, or you should accept lower output at that moisture.

Is a material trial necessary?

For new products, unusual feeds or tight quality targets, a trial reduces risk. It shows drying behaviour, product quality and end-point moisture before sizing is final.

Related guides and GTI equipment

This guide is part of GTI’s coconut processing series. Related reading and equipment:

GTI video: coconut processing machinery for desiccated coconut, VCO, milk and water (GTI YouTube channel).

Sources

About this article

Prepared by the Genex Tech Industries LLP (GTI Group) editorial team as a procurement checklist. The capacity table is an illustrative calculation; heat figures are theoretical minimums, not dryer performance data.

Send GTI your data sheet

GTI Group, engineering since 1985, designs and supplies dryers and complete coconut processing lines. Send us your completed data sheet and we will reply with a quotation that states its mass balance, utilities and scope clearly.

Request a quotation for a coconut dryer or processing line

Send your capacity, product specification and site details through our quotation request form, and GTI Group will respond with a proposal.

For more information, email mktg@coconutprojects.com or call or WhatsApp us on +91-87774 75596.

Scroll to Top