Short answer: a coconut dryer performance test should prove the duty the contract guarantees, at the feed conditions the guarantee assumes. Weigh the wet feed and the product over an agreed steady-state period. Measure feed and product moisture by the agreed laboratory method. Check that dry solids in equal dry solids out within an agreed tolerance. Then calculate water evaporated, thermal energy per kilogram of water, and electrical energy, kept separate. Do not accept “it made 500 kg/h” on its own. If the feed was drier than the design feed, the dryer evaporated less water than the guarantee requires, and the test has not proved the design duty.

This guide is for plant owners, project engineers and consultants commissioning a band, fluid bed or spray dryer for desiccated coconut, chips, flour, parings, powders or shell products. It follows our coconut dryer quotation checklist, which covers how to write guarantees before ordering.
Agree the test before the dryer arrives
Most disputes at handover come from tests that were never defined. Write the test procedure into the contract, or attach it as an annex:
- Guaranteed duty. Product rate and moisture, design feed moisture range, and the water evaporation rate those figures imply.
- Test conditions. Feed quality, ambient conditions, steam pressure or fuel, and the allowed deviation from design.
- Steady state. How it is defined, for example outlet air temperature and product moisture stable for an agreed period before the test clock starts, and the minimum test duration.
- Methods. The moisture method and sampling plan. Our guide to moisture testing and sampling in coconut plants explains why this matters.
- Tolerances. Mass-balance closure, measurement uncertainty, and how results will be corrected if the test feed differs from design.
- Quality criteria. Colour, specks, oil acidity, microbiology or other product tests, with the method for each.
A factory acceptance test (FAT) at the supplier’s works can check mechanical function, controls and safety interlocks. Product performance depends on your feed, so it normally needs a site acceptance test (SAT) after commissioning.
What to measure
| Quantity | How | Frequency |
|---|---|---|
| Wet feed mass | Calibrated platform scale or load cells; weigh every batch or tote | Whole test |
| Product mass | Weigh all product, including grade fractions | Whole test |
| Fines and rejects | Weigh cyclone or bag-filter catch and oversize | Whole test |
| Feed moisture | Reference oven method, duplicate samples | For example every 30 minutes |
| Product moisture | Reference method; samples across the outlet width | For example every 30 minutes |
| Inlet and outlet air temperature, humidity | Calibrated sensors; record the control-system trend | Continuous |
| Thermal input | Steam flow meter, or weighed condensate; fuel mass and calorific value for direct firing | Whole test |
| Electrical input | Power meter on the dryer’s own feeders (fans, drives, conveyors) | Whole test |
| Product quality | Agreed tests (colour, specks, FFA, microbiology) | Composite and spot samples |
Plan raw material for the whole test. Using the planning figure of about 10 kg of desiccated coconut per 100 nuts from our plant sizing mass balance, a 4-hour test at about 510 kg/h of product needs roughly 20,000 nuts of consistent quality, plus nuts for start-up and stabilisation.
Planning a coconut dryer with a defined acceptance test? Request a quotation from GTI.
Tell us your product, target capacity, raw-material data and site location. GTI Group engineers will review it and prepare a proposal for your project, in India or abroad.
Worked example: evaluating a test
Illustrative example, not GTI test data. Desiccated coconut dryer. Guarantee: 500 kg/h of product at 3.0% maximum moisture (wet basis), from feed at 55% wet basis. Steady-state test duration: 4 hours.
| Measured over 4 hours | Value |
|---|---|
| Wet feed | 4,160 kg at 52.0% moisture |
| Product | 2,040 kg at 2.8% moisture |
| Cyclone fines | 25 kg at 3.0% moisture |
| Steam (condensate weighed) | 2,800 kg at 8 bar absolute, saturated |
| Dryer electrical consumption | 184 kWh (average 46 kW) |
Step 1: check the solids balance
Solids in = 4,160 × 0.480 = 1,996.8 kg. Solids out = 2,040 × 0.972 + 25 × 0.970 = 1,982.9 + 24.3 = 2,007.2 kg. Closure = +0.5%. If the contract tolerance were, say, ±2% (an illustrative figure), this test would pass the check, and the weighing and moisture data can be treated as consistent. A large gap means a weighing error, unrepresentative moisture samples or unrecorded losses. Find the cause before using the results.
Step 2: calculate the evaporation rate
Water evaporated = feed − product − fines = 4,160 − 2,040 − 25 = 2,095 kg, or about 524 kg/h. Calculating from the water balance instead (2,163 kg in, 58 kg left in product and fines) gives 2,105 kg. The 0.5% difference is the closure gap from Step 1.
Step 3: compare with the guarantee on the right basis
The product rate was 510 kg/h at 2.8%, apparently above the 500 kg/h guarantee. The feed, however, was at 52% rather than the design 55%. At design conditions, 500 kg/h at 3.0% contains 485 kg/h of solids. That needs 485 ÷ 0.45 = 1,078 kg/h of feed and 578 kg/h of evaporation. The test showed 524 kg/h. It has therefore not demonstrated the design duty, even though product output looked sufficient. Either repeat the test with design-moisture feed, or apply a correction method agreed in the contract. The water evaporation rate is the fair comparison, because the feed moisture can vary.
Step 4: thermal energy per kilogram of water
Steam at 8 bar absolute has a latent heat of about 2,048 kJ/kg (NIST steam properties). Assuming condensate leaves saturated, heat input = 700 kg/h × 2,048 = about 1,434,000 kJ/h, or about 398 kW. Specific thermal consumption = 1,434,000 ÷ 524 = about 2.74 MJ per kg of water evaporated. For comparison, the latent heat of water at typical dryer conditions is about 2.4 MJ/kg. The difference covers heating the product and air, the exhaust and casing losses. If condensate is sub-cooled or flash steam is lost, the heat calculation must account for it.
Step 5: electrical energy, reported separately
46 kW ÷ 524 kg/h = about 0.088 kWh per kg of water, or 0.090 kWh per kg of product. Never add kWh of electricity to MJ of steam in one “energy” figure. They have different costs and sources. GTI’s guide to dryer energy audits and specific energy consumption explains how to track both over time.
Quality is part of performance
A dryer that reaches its evaporation rate but yellows the product, chars fines or leaves wet edges has not passed. Include in the acceptance criteria:
- Moisture spread across the outlet width, as well as the average. Uneven drying in a band dryer shows up here. GTI’s uneven moisture troubleshooting guide explains the causes.
- Colour and specks against the contract limits. Our article on brown specks and foreign matter covers their origins.
- Product temperature at packing, after the cooling stage.
- Microbiological results where the contract requires them. The dryer is not the kill step, as explained in our Salmonella control article.
Adapting the test to other dryer types
- Vibratory and combination fluid bed dryers: weigh cyclone fines carefully, because they are a larger share of the solids balance, and record the bed pressure drop.
- Spray dryers: measure feed solids rather than moisture, weigh powder from every collection point, and record wall deposits after the test. The AIChE guide to spray dryer performance evaluation gives a detailed framework.
- Direct-fired dryers: measure fuel mass and calorific value in place of steam. The AIChE guide for continuous direct-heat rotary dryers covers heat and mass balances for these systems.
Test-day checklist
- Instruments calibrated and calibration certificates available; scales checked with test weights.
- Dryer clean, run in, and stable at the agreed settings.
- Enough consistent raw material for start-up and the full test period.
- Sampling plan, sample containers and laboratory capacity ready.
- Data sheet with both parties’ signatures for each reading.
- Agreed calculation sheet: solids closure, evaporation, thermal and electrical consumption, quality results.
For complete projects, GTI’s turnkey drying scope covers design through installation and commissioning.
FAQ
How long should a performance test run?
Long enough, after steady state, for the weighing and moisture sampling to give reliable averages. Agree the duration in the contract. Several hours is common for continuous dryers, but no universal figure applies.
Who should take the samples?
Both parties, or an agreed independent laboratory, using split samples from the same containers.
Are the example figures GTI performance data?
No. They are illustrative numbers chosen to show the calculations.
Related guides and GTI equipment
This guide is part of GTI’s coconut processing series. Related reading and equipment:
- coconut dryer quotation checklist: writing the guarantee before ordering.
- moisture testing methods: the agreed moisture method.
- DC plant sizing mass balance: the design duty to test.
- GTI band dryer: dryer page.
- GTI combination fluid bed dryer: dryer page.
Sources
- AIChE Equipment Testing Procedure Committee, Spray Dryers: A Guide to Performance Evaluation, 2nd edition, Wiley.
- AIChE, Continuous Direct-Heat Rotary Dryers: A Guide to Performance Evaluation, 3rd edition, 2005.
- NIST Chemistry WebBook, Thermophysical Properties of Fluid Systems (saturated steam properties).
- Codex Alimentarius, Standard for Desiccated Coconut, CXS 177-1991 (moisture method AOAC 925.40).
- Department of Standards Malaysia, MS 1381:1995 Specification for Desiccated Coconut (oven moisture method).
About this article
Prepared by the Genex Tech Industries LLP (GTI Group) editorial team as a commissioning framework. The worked example uses illustrative numbers. Actual acceptance criteria and correction methods should be agreed between buyer and supplier in the contract and reviewed by the project engineer.
Plan your dryer acceptance test with GTI
GTI Group, engineering since 1985, designs, supplies and commissions dryers for coconut products. Ask us for a test procedure matched to your guarantee and product.
Request a quotation for a coconut dryer with a defined acceptance test
Send your capacity, product specification and site details through our quotation request form, and GTI Group will respond with a proposal.
For more information, email mktg@coconutprojects.com or call or WhatsApp us on +91-87774 75596.
