Short answer: to size a desiccated coconut (DC) plant, work backwards from the finished output. Convert output to dry solids, use the moisture of the wet gratings to find the dryer feed rate and evaporation load, then use a realistic recovery per nut to find how many coconuts per hour the front end must handle. In the illustrative example below, 500 kg/h of DC at 3% moisture needs about 970–1,080 kg/h of wet gratings, means evaporating about 470–580 kg/h of water, and needs roughly 5,000 nuts per hour at an average recovery of 10 kg of DC per 100 nuts.
This worked method is for entrepreneurs, consultants and project engineers preparing a feasibility study or comparing supplier quotations. It explains which numbers to ask for and why “capacity” on a quotation can mean three different things.
Three capacity terms you must keep separate
- Finished-product output: kg/h of dried, sieved DC at the specified moisture. GTI’s desiccated coconut processing plant capacities (100 to 2,500 kg/h) and dryer model tables are stated as output of made or dried DC.
- Wet-feed capacity: kg/h of wet gratings entering the dryer. Grinders and conveyors are usually rated on this basis. GTI’s DC cutter or grinder, for example, is rated up to 1,000 kg of wet coconut meat per hour.
- Evaporation rate: kg/h of water removed. This sets the dryer’s heat load, airflow and utility demand.
A dryer that delivers 500 kg/h of output does not take 500 kg/h of feed. Mixing up these three figures is one of the most common mistakes in early plant planning.
Reference data used
| Input | Value used | Source |
|---|---|---|
| Finished DC moisture | 3% (wet basis) | GTI DC plant page lists 2–3%. Codex CXS 177-1991 sets a maximum of 4% m/m |
| Wet gratings moisture at dryer inlet | 50% and 55% (wet basis), as two cases | GTI band dryer page: input moisture about 50–55% |
| Average recovery | About 10 kg DC per 100 nuts | Coconut Development Board (India), DC project profile, which notes that recovery depends on nut quality |
| Paring loss | 12–15% of kernel | Same CDB profile |
| Latent heat of water (approximate) | 2,400 kJ/kg | Standard steam-table value, rounded, for 40–60 °C |
All numbers in the example below are illustrative. They show the method, not a guaranteed result for your nuts, your dryer or your site.
Worked example: 500 kg/h of finished DC
Step 1: dry solids in the output
500 kg/h × (1 − 0.03) = 485 kg/h of dry solids. Solids pass through the dryer unchanged. Only water is removed.
Step 2: wet feed to the dryer
Wet feed = dry solids ÷ (1 − inlet moisture, wet basis).
- At 50% inlet moisture: 485 ÷ 0.50 = 970 kg/h
- At 55% inlet moisture: 485 ÷ 0.45 = about 1,078 kg/h
Step 3: evaporation load
Evaporation = wet feed − finished output.
- At 50%: 970 − 500 = 470 kg/h of water
- At 55%: 1,078 − 500 = about 578 kg/h of water
A five-point rise in inlet moisture increases the evaporation load by about 23%. That is why washing water carry-over and blanching conditions affect dryer sizing.
Step 4: minimum heat needed just to evaporate the water
470 kg/h × 2,400 kJ/kg ≈ 1,128,000 kJ/h ≈ 313 kW. At 578 kg/h, it is about 385 kW.
This is a theoretical minimum thermal load for evaporation only. Real dryers need more heat to warm the product and the air, and to cover exhaust and shell losses. The actual thermal demand depends on dryer design, air recirculation and heat recovery, and the supplier must state it. Electrical load for fans, vibration motors, conveyors and controls is separate and must be listed separately in the quotation.
Step 5: nuts per hour
At about 0.1 kg of DC per nut, 500 kg/h ÷ 0.1 = about 5,000 nuts per hour, or about 100,000 nuts in a 20-hour operating day. Recovery below the CDB average, for example from immature or poorly stored nuts, raises this number directly.
Step 6: cross-check the front end
Each machine before the dryer has to keep up with the nut and wet-feed rates. Using capacities published on GTI’s DC plant page:
| Station | Published GTI capacity | Illustrative requirement | Indicative count |
|---|---|---|---|
| Deshelling machine | 350–425 nuts/h per machine | 5,000 nuts/h | 12–15 machines (5,000 ÷ 425 = 11.8; 5,000 ÷ 350 = 14.3) |
| DC cutter or grinder | Up to 1,000 kg wet meat/h | 970–1,078 kg/h | At or above the limit of one unit, so plan two or confirm with GTI |
| Dryer | For example, Standard VFBD 450–550 kg/h of dried DC, or a 6-module combination dryer 500–550 kg/h | 500 kg/h output | One unit is near its upper range; check margin |
Paring stations and labour are not sized here. Manual and mechanical paring rates vary widely and should be confirmed during plant design.
Step 7: by-product stream
If 12–15% of the kernel goes to parings, the paring stream in this example is roughly 130–170 kg/h of wet parings. This estimate assumes the pared kernel per nut implied by Step 2 at 50% moisture. That is enough material to justify assessing a paring oil line or paring drying in the feasibility study rather than treating parings as waste. Our sister site describes dryer options for coconut paring skin.
Quick formula sheet
| Quantity | Formula (wet-basis moisture as a fraction) |
|---|---|
| Dry solids (S) | Output × (1 − Mout) |
| Wet feed | S ÷ (1 − Min) |
| Evaporation | Wet feed − Output |
| Minimum evaporation heat (kW) | Evaporation (kg/h) × 2,400 ÷ 3,600 |
| Nuts per hour | Output ÷ DC recovery per nut |
Wet basis vs dry basis: 50% moisture on a wet basis means 1 kg of water per 1 kg of dry solids, which is 100% on a dry basis. Always confirm which basis a specification or quotation uses.
What to ask suppliers so quotations are comparable
- Is the stated capacity finished output, wet feed or evaporation?
- What inlet and outlet moisture (and basis) is the capacity based on?
- What is the thermal energy demand (kW or kcal/h) at that duty, and with which heating medium: steam, thermic fluid or hot air?
- What is the connected and running electrical load?
- What capacity margin is included for higher inlet moisture?
- Which front-end machines are included, and how many, for the stated nut rate?
- Can trials be run on your nuts before you finalise sizing?
Frequently asked questions
Why does my dryer not reach its rated output?
A common reason is that the inlet moisture is higher than the design basis. In the example, moving from 50% to 55% inlet moisture raises evaporation by about 23% at the same output. Check feed moisture before suspecting the dryer.
Is 10 kg of DC per 100 nuts a guaranteed yield?
No. It is an average reported by India’s Coconut Development Board, and recovery depends on nut quality and maturity. Use your own trial data where possible.
Should I size the dryer exactly to my target output?
Most planners keep some margin for moisture variation and future growth. How much margin to keep is a design decision to agree with the supplier during engineering review.
About this article
Prepared by the Genex Tech Industries LLP (GTI Group) editorial team. Calculations were checked arithmetically and use the stated assumptions and sources. They are illustrative and are not performance guarantees. Final sizing requires engineering review and, ideally, material trials.
Get your DC plant sized
Genex Tech Industries LLP (GTI Group) designs complete desiccated coconut plants, from dehusking and deshelling through blanching, drying, cooling, grading and packing. Send us your target output and nut data for a sizing discussion.
For more information, email mktg@coconutprojects.com or call or WhatsApp us on +91-87774 75596.
