Short answer: a tonne of coconut oil contains only about 80–170 kg of the caprylic (C8) and capric (C10) acids that make up commercial MCT oil. Even with complete recovery, that means roughly 80–185 kg of MCT oil per tonne of feedstock. Everything else comes out as other products: a large lauric–myristic acid cut, a heavier fatty acid cut and about 140 kg of glycerol. An MCT plant built on coconut oil is really a fat-splitting and fatty acid distillation plant with an MCT line attached. Whether the project pays depends as much on selling those co-products as on the MCT price.

This article is for coconut oil processors, ingredient companies and consultants evaluating MCT oil. It works through the stoichiometry, compares the published process routes and lists what to specify before requesting a quotation.
Why coconut oil is not “MCT oil”
Coconut oil is rich in medium-chain fatty acids, but these sit on the same glycerol molecules as long-chain acids. A 2026 review in Nutrients notes that natural oils contain medium-chain fatty acids only in combination with long-chain ones. Making pure MCTs therefore needs a dedicated process: release the fatty acids, separate them by chain length, then rebuild triglycerides from the C8 and C10 fraction.
The Asian and Pacific Coconut Community (APCC, now the International Coconut Community) standard for virgin coconut oil gives these fatty acid ranges by gas chromatography:
| Fatty acid | Chain | Range in coconut oil (%) | Where it goes in an MCT plant |
|---|---|---|---|
| Caproic | C6:0 | 0.10–0.95 | Light ends; partly in MCT cut |
| Caprylic | C8:0 | 4–10 | MCT cut |
| Capric | C10:0 | 4–8 | MCT cut |
| Lauric | C12:0 | 45–56 | Main co-product cut |
| Myristic | C14:0 | 16–21 | Main co-product cut |
| Palmitic, stearic, oleic, linoleic | C16–C18 | about 15–27 combined | Heavy cut |
So C8 plus C10 is about 8–18% of the fatty acids. That single number drives the whole mass balance.
Worked mass balance per tonne of coconut oil
Basis and assumptions: refined or virgin coconut oil with a saponification value of 250–260 mg KOH/g (the APCC range); complete hydrolysis; MCT made as a 70:30 C8:C10 blend by mass; no distillation or handling losses. This is a theoretical ceiling, not a plant yield.
- Splitting. At a saponification value of 255 mg KOH/g, one gram of oil holds about 4.55 mmol of fatty acid. Hydrolysis adds about 82 kg of water per tonne and releases about 140 kg of glycerol. That leaves about 942 kg of mixed fatty acids. Across 250–260 mg KOH/g, the results are 941–943 kg of fatty acids and 137–142 kg of glycerol.
- MCT fraction. 942 kg × 8–18% = about 75–170 kg of C8/C10 acids. A mid-range oil (12–14%) gives about 113–132 kg.
- Re-esterification. Rebuilding a 70:30 C8:C10 triglyceride needs about 0.20 kg of glycerol per kg of acids. It gives about 1.08 kg of MCT per kg of acids, because the glycerol backbone adds mass and water is removed.
- Theoretical MCT. About 80–185 kg per tonne of oil, or about 123–143 kg for a mid-range oil.
Two practical points follow. First, re-esterification uses only about 15–35 kg of glycerol per tonne of oil, while splitting releases about 140 kg. Most glycerol is surplus, as a dilute “sweetwater” that needs concentration and refining before sale. Second, real recovery is lower than this ceiling. Distillation cuts overlap, so some C10 leaves with the lauric cut and some C12 enters the MCT cut. A 2024 review in Phytochemistry Reviews describes three cuts from coconut fatty acids: about 10–15% medium-chain acids, 50–70% mainly lauric and myristic, and 15–20% heavier acids. Those figures are consistent with the calculation above.
| Stream per tonne of coconut oil (theoretical) | Approximate quantity | Typical outlet |
|---|---|---|
| MCT oil (C8/C10 triglyceride) | 80–185 kg | Food, nutrition, cosmetic and pharmaceutical carriers |
| Lauric–myristic acid cut | roughly 550–700 kg | Oleochemicals, surfactants, soaps |
| Heavy fatty acid cut | roughly 140–250 kg | Oleochemicals, soaps, feed fats (market-dependent) |
| Glycerol (as crude sweetwater) | about 137–142 kg pure basis, of which about 15–35 kg can be reused in esterification | Refined glycerine markets |
The co-product ranges are our estimates, calculated from the APCC fatty acid ranges. Your oil’s actual chromatogram will move every line in this table.
Planning an MCT oil plant? Request a quotation from GTI.
Tell us your product, target capacity, raw-material data and site location. GTI Group engineers will review it and prepare a proposal for your project, in India or abroad.
Three process routes compared
Published reviews describe three main ways to get from coconut oil to MCT. The table summarises them. Operating conditions are those reported in the literature, not GTI design values.
| Route | Key steps | Reported conditions | Strengths | Watch-outs |
|---|---|---|---|---|
| A. Hydrolysis, distillation and direct esterification | High-pressure steam splitting; vacuum fractional distillation of fatty acids; esterification of the C8/C10 cut with glycerol; removal of excess acids; refining and deodorisation | Esterification at 160 °C or above with continuous water removal; often above 200 °C | Solvent-free; the most widely described industrial route; co-products are free fatty acids | High-temperature, high-vacuum duty; deacidification and deodorisation needed; colour and odour control |
| B. Methanolysis and methyl ester fractionation | Convert oil to methyl esters and glycerol; distil the esters by chain length; then esterify directly with glycerol or hydrolyse to free acids first | Base-catalysed methanolysis | Ester distillation is well established; it overlaps with coconut biodiesel (CME) technology | Methanol handling and recovery; an extra conversion step if free acids are needed |
| C. Enzymatic esterification | Immobilised lipase joins glycerol with C8/C10 acids | Milder temperatures; very long reaction times reported | Fewer side reactions; less colour formation | Enzyme cost and life; slow batches; still needs fatty acid fractionation upstream |
A small study published in AIP Conference Proceedings (2020) shows that virgin coconut oil can also be the starting oil. It reported 81.74% (w/w) medium-chain fatty acids from low-pressure fractional distillation at 130–140 °C, followed by esterification with glycerol at 170 °C and 40 kPa. That was laboratory work; plant designs need pilot data.
What GTI’s MCT plant scope covers
Genex Tech Industries LLP (GTI Group) offers a turnkey MCT oil processing plant. Its listed equipment includes coconut oil storage, pre-treatment and filtration, a hydrolysis/esterification reactor, a fractionation column, molecular distillation, deodorisation, a vacuum system, heat exchangers, polishing filtration and PLC automation. Steam or thermic fluid heating is used, with SS316/SS304 construction. Route A maps directly onto that equipment list. For a longer description of the equipment, see our group article on MCT oil plant engineering.
The process choice, column design and achievable C8/C10 purity depend on your feedstock analysis, target product specification and capacity. These must be confirmed through engineering review and, where needed, trials.
Specifying the product before the plant
- C8:C10 ratio. The Phytochemistry Reviews paper reports commercial products ranging from 95:5 to 5:95, with 70:30 the most common, and generally less than 6% of other medium-chain acids (C6, C12). A high-C8 product needs sharper fractionation and lowers yield per tonne of oil.
- Purity and residuals. Set limits for acid value, residual mono- and diglycerides, colour, odour and moisture, and ask how each is controlled.
- Regulatory route. Reviews describe MCT as generally recognised as safe (GRAS) in the United States. In the EU it is used mainly in foods for special medical purposes, and in Japan in functional food systems. Confirm the rules in each target market before fixing claims or grades.
- Liquid or powder. Many sports and keto products use MCT powder. That is a separate encapsulation and drying step, similar in principle to our VCO powder processing plant. It is built around a spray dryer and needs carrier and emulsion trials. GTI Dryers also describes oil-powder drying systems.
Utilities: separate thermal from electrical
Thermal energy goes to splitting, distillation, esterification and deodorisation, mostly at high temperature and under vacuum. Electrical load comes from vacuum pumps, process pumps, agitators and cooling water. We do not quote consumption figures because they depend on route, heat recovery and capacity. Ask for a utility schedule listing steam or thermic fluid, cooling water and electrical load separately for each section.
Is MCT the right next product for your plant?
MCT tends to fit best where three conditions are met:
- You already produce or buy coconut oil reliably. Our virgin coconut oil machinery page and the group’s oil expellers cover the upstream side. Our note on coconut raw-material costs heading into 2027 discusses feedstock price risk.
- You have a buyer for more than half a tonne of lauric–myristic acids per tonne of oil processed, or a plan to make value-added products from them.
- Your scale justifies high-vacuum distillation. Small batches of MCT are possible, but the fatty acid fractionation step sets the economics.
If the methyl ester route interests you, the chemistry overlaps with our coconut biodiesel plant. Our analysis of CME blend policy and plant planning covers that market. Oil quality upstream also matters: moisture and free fatty acids, discussed in our guide to VCO moisture, FFA and peroxide control, affect pre-treatment.
Buyer checklist for an MCT oil plant enquiry
- A fatty acid profile (GC) of your actual oil, with saponification value, FFA and moisture.
- Target product: C8:C10 ratio, purity, grade (food, nutraceutical, pharmaceutical) and form (liquid or powder).
- Capacity, stated as MCT output per day and oil input per day. These differ by roughly a factor of 5–12.
- A co-product plan for the lauric–myristic cut, the heavy cut and glycerol.
- Preferred route (A, B or C) and any restrictions on catalysts or methanol.
- Available utilities: steam pressure, thermic fluid, cooling water, power.
- Documentation needs for your target markets.
FAQ
How much coconut oil do I need for 1 tonne of MCT oil?
Theoretically, about 5.4–12.5 tonnes, depending on the oil’s C8/C10 content. In practice it will be more, because of fractionation overlaps and losses. Use your own GC data and a supplier mass balance.
Can VCO be used instead of refined coconut oil?
Yes, technically. Published laboratory work has used VCO. But the value of “virgin” status is lost after splitting and deodorisation, so the choice is usually about cost and availability.
Are the yields in this article GTI guarantees?
No. They are stoichiometric ceilings based on published composition ranges. Plant performance must be established for your feedstock and design.
Related guides and GTI equipment
This guide is part of GTI’s coconut processing series. Related reading and equipment:
- VCO moisture, FFA and peroxide control: feedstock oil quality.
- coconut biodiesel (CME) plant planning: another oleochemical route.
- coconut oil price signals: feedstock cost.
- GTI MCT oil processing plant: turnkey MCT line.
- MCT oil plant on foodtechprojects.com: group page.
Sources
- Asian and Pacific Coconut Community, APCC Quality Standard for Virgin Coconut Oil (amended 2009): saponification value and fatty acid ranges.
- Medium-Chain Triglycerides: Scientific and Regulatory Perspectives from Germany and Japan with a US Context, Nutrients 18(7):1027, March 2026.
- Coconut-sourced MCT oil: its potential health benefits beyond traditional coconut oil, Phytochemistry Reviews, 2024.
- Triglycerides of medium-chain fatty acids: a concise review, Journal of Food Science and Technology, 2022.
- Synthesis and characterization of medium-chain triglyceride (MCT) from virgin coconut oil, AIP Conference Proceedings, 2020 (doi 10.1063/5.0001449), abstract.
About this article
Prepared by the Genex Tech Industries LLP (GTI Group) editorial team from the published sources listed. All calculations are theoretical and illustrative. They are not performance guarantees. Process design requires feedstock analysis, pilot data where appropriate and engineering review.
Discuss an MCT oil project with GTI
GTI Group, engineering since 1985, supplies coconut processing plants including MCT oil, virgin coconut oil and oil-powder lines. Share your oil analysis, target specification and capacity, and our engineers can work through the mass balance with you.
Request a quotation for an MCT oil plant
Send your capacity, product specification and site details through our quotation request form, and GTI Group will respond with a proposal.
For more information, email mktg@coconutprojects.com or call or WhatsApp us on +91-87774 75596.
