Desiccated Coconut Grades Explained: How to Specify Extra-Fine, Fine and Medium, and Size the Grading Line

Short answer: under the Codex standard for desiccated coconut (CXS 177-1991), each size grade is defined by two sieves, not one. The upper sieve limits oversize and the lower sieve limits fines. Fine desiccated coconut, for example, needs at least 80% by weight to pass a 1.40 mm sieve, with no more than 20% passing 0.71 mm. Trade names such as “macaroon”, “coarse” or “chips” are not Codex grades and must be defined in the contract. In the plant, grade yield is set by the grinder setting, then sorted by the grader and sifter. A multi-deck grader lets one grinder output be split into several saleable grades.

Stainless steel multi-layer grading machine with discharge chutes for desiccated coconut
GTI grading machine for desiccated coconut grades. Image: GTI Group (coconutprojects.com).

This guide is for desiccated coconut (DC) producers, buyers writing specifications and engineers selecting grading equipment. It explains the Codex definitions, shows a worked example of turning one grinder output into three grades, and lists what to put in a contract.

The Codex size grades in plain numbers

Codex grade Upper sieve: minimum % passing Lower sieve: maximum % passing Approximate US sieve numbers (ASTM E11)
Extra-fine 90% through 0.85 mm 25% through 0.50 mm No. 20 / No. 35
Fine 80% through 1.40 mm 20% through 0.71 mm No. 14 / No. 25
Medium 90% through 2.80 mm 20% through 1.40 mm No. 7 / No. 14
Other sized All other presentations, including fancy or special cuts: thin flakes, long chips, shreds and similar. Not defined by Codex sieve limits

Source: Codex CXS 177-1991, Section 2.2. Sizing is optional under the standard. Sieve-number equivalents are given for convenience; always specify the aperture in millimetres.

How to read the two-sieve rule

The upper sieve stops a “fine” lot from containing too many large pieces. The lower sieve stops it from being mostly powder. A lot that meets only the first limit can still be rejected as dusty. When a customer complains that a grade is “too powdery”, the lower-sieve result is usually the one to check.

The composition limits that apply to every grade

Parameter (Codex CXS 177) Requirement
Moisture max 4% m/m
Oil content min 60% m/m (full-fat); 35% to below 60% for partially defatted DC
Total acidity of extracted oil max 0.3% m/m as lauric acid
Ash max 2.5% m/m
Extraneous vegetable material max 15 fragments per 100 g
Foreign matter absent in 100 g
Colour, odour natural white to light creamy white; not mouldy, cheesy, smoky, fermented or rancid

Many buyers ask for a tighter moisture than the Codex maximum. GTI’s desiccated coconut processing plant is specified for 2–3% moisture output. Particle size and moisture interact: fine particles pick up moisture faster in humid packing halls, so the tighter grade usually needs the tighter humidity control.

Planning a desiccated coconut grading and sieving line? Request a quotation from GTI.

Tell us your product, target capacity, raw-material data and site location. GTI Group engineers will review it and prepare a proposal for your project, in India or abroad.

Request a quotation →

Where particle size is decided in the line

  1. Grinding or cutting sets the size distribution. GTI’s DC cutter or grinder is adjustable for different sizes and can also produce chips and threads.
  2. Blanching and drying shrink the particles as water is removed, and rough handling creates fines. Drying from about 50% to 3% moisture removes roughly half the wet weight, so particles shrink noticeably.
  3. Cooling comes before sieving in GTI’s process flow. Warm, oily DC is more prone to clumping and to smearing on the mesh.
  4. Grading and sifting separate the stream into grades. GTI’s grading machine uses a five-layer mesh with six discharge points, and the plant equipment list includes a vibro sifter.

Worked example: one grinder output, three grades

Illustrative only. Suppose a sieve test on cooled, dried DC from one grinder setting gives the distribution below. A five-deck grader is fitted with the Codex apertures, so each discharge collects one size band.

Grader discharge (size band) Share of stream
Retained on 2.80 mm (oversize) 8%
1.40–2.80 mm 32%
0.85–1.40 mm 30%
0.71–0.85 mm 8%
0.50–0.71 mm 10%
Below 0.50 mm 12%

Step 1: is the whole stream sellable as one grade? As Medium, 92% passes 2.80 mm (meets the 90% minimum), but 60% passes 1.40 mm, three times the 20% maximum. As Fine, only 60% passes 1.40 mm (below the 80% minimum) and 22% passes 0.71 mm (above the 20% maximum). The unsorted stream fails both.

Step 2: build grades from the size bands.

  • Medium: the 1.40–2.80 mm band alone, 32% of the stream. All of it passes 2.80 mm and, with ideal sieving, none passes 1.40 mm.
  • Fine: the 0.85–1.40 mm and 0.71–0.85 mm bands (38%), plus some material below 0.71 mm. Fine allows up to 20% passing 0.71 mm, so up to 0.20 × 38 ÷ 0.80 = 9.5% can be added. Adding 9% gives a Fine grade of 47%, of which 19% passes 0.71 mm.
  • Extra-fine: the 0.50–0.71 mm band (10%) plus some material below 0.50 mm. Extra-fine allows up to 25% passing 0.50 mm, so up to 3.3% can be added. Adding 3% gives an Extra-fine grade of 13%, with 23% passing 0.50 mm.
  • Oversize: 8%, to be reground or sold as a special cut if a buyer accepts it.

Check: 8 + 32 + 47 + 13 = 100%. All the below-0.50 mm material (9 + 3 = 12%) has been absorbed into graded product.

What the example shows. Codex limits make grading partly a blending exercise. The fines allowance in each grade is a real outlet for fines, and wasting it costs yield. Real sieves are not perfectly sharp, though. Some fines stay on each deck, and worn or blinded mesh lets oversize through. Design to a margin, for example 15% rather than 20% fines, and confirm with laboratory test sieves.

Changing the grinder setting changes everything. If the market wants mostly Fine, a finer cut moves material from the 1.40–2.80 mm band into the Fine bands, but it also creates more dust. The right setting comes from trial grinding and sieve tests on your own nuts, not from a table.

Sizing the grading and sifting step

  • Throughput: size the grader on the dried, cooled output rate. GTI’s grading machine page quotes capacities from 500 kg/h up to 1,000 kg/h for the higher-capacity model, so a 500 kg/h plant is at the lower model’s rating. Confirm the rating for your size distribution: fine cuts load the lower decks more heavily.
  • Number of decks: one deck per cut point you need to control. Producing Medium, Fine and Extra-fine to Codex needs the five apertures in the example (2.80, 1.40, 0.85, 0.71 and 0.50 mm). Fewer decks are enough if you sell fewer grades.
  • Mesh and cleaning: detachable meshes simplify cleaning and changeovers. Inspect mesh regularly for tears, because a torn screen sends oversize into a fine grade.
  • Foreign-matter control: Codex requires absence of foreign matter in 100 g. Sifting, magnets and a metal detector before packing are separate safeguards; GTI’s DC equipment list includes a metal detector.
  • Packing: different grades flow differently in weighers. GTI’s packing machinery includes vibratory tables for medium and fine grades.

For stand-alone sieving equipment, see the gyratory sifter and grading machine pages on our sister site. Drying choices that affect particle integrity are covered on GTI’s vibratory fluid bed dryer page and the desiccated coconut drying page.

What to write into a DC contract

  • The grade name and its two sieve limits, in millimetres, or “as per Codex CXS 177-1991, Section 2.2”.
  • For trade names such as “macaroon” or “coarse”, the actual sieve apertures and percentages agreed.
  • The sieving method: sample mass, sieve standard (for example ISO 3310-1 test sieves), shaking time and amplitude.
  • Moisture limit and method (Codex lists AOAC 925.40, loss on drying).
  • Oil content (full-fat or partially defatted) and acidity limit.
  • Microbiological criteria. See our article on Salmonella control in desiccated coconut.
  • Packaging, which matters more for fine grades in humid climates.

Frequently asked questions

Is “coarse desiccated coconut” a Codex grade?

No. Codex defines Extra-fine, Fine and Medium, plus “other sized” presentations. Any other name needs its own sieve definition in the contract.

Can I sell the dust below 0.50 mm?

Partly within graded products, as the example shows, because each grade has a fines allowance. Any surplus can be sold as a separate ingredient where buyers accept it, or used in by-product streams. Our article on coconut flour from residue describes one such outlet for a related stream.

Why do two laboratories get different sieve results on the same lot?

Sample size, shaking time, sieve condition and humidity all affect results. Agree the method in the contract and exchange reference samples.

Related guides and GTI equipment

This guide is part of GTI’s coconut processing series. Related reading and equipment:

GTI video: specialised cutter for desiccated coconut powder and coconut chips (GTI YouTube channel).

Sources

About this article

Prepared by the Genex Tech Industries LLP (GTI Group) editorial team. The size distribution in the worked example is illustrative, not measured data. Actual grade yields depend on nuts, grinder setting, drying and sieving efficiency, and should be confirmed by trials.

Get your DC grading line specified

Genex Tech Industries LLP (GTI Group), engineering since 1985, supplies complete desiccated coconut plants from dehusking to grading and packing. Tell us the grades your buyers want and your target output, and we can discuss grinder, grader and sifter selection.

Request a quotation for a desiccated coconut grading and sieving line

Send your capacity, product specification and site details through our quotation request form, and GTI Group will respond with a proposal.

For more information, email mktg@coconutprojects.com or call or WhatsApp us on +91-87774 75596.

Scroll to Top